Gibson Guitar Board: Jog Wheels - Help, Please!! - Gibson Guitar Board

Jump to content

Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Jog Wheels - Help, Please!!

#1 User is offline   azzi 

  • Member
  • Group: Members
  • Posts: 11
  • Joined: 21-November 12

Posted 03 September 2015 - 10:54 AM

Friends, I need help! My Stanton SCS4DJ is presenting a sore left Jog ... I live in Brazil and found technical assistance to remedy the defect.

Take a look at this video: https://www.youtube....h?v=upa9cBpA6DA

Music is my life!
0

#2 User is offline   eljeffe 

  • Member
  • Group: Members
  • Posts: 47
  • Joined: 02-March 15

Posted 03 September 2015 - 12:29 PM

This could be a very easy fix - I fixed a different but related problem the other day.

Yours is behaving just as if the platter surface is not reacting - the wheel still works (you can see the pitch bend), but the scratch is never engaged because the surface doesn't seem to work.

You just have to get into the unit and see for yourself - take the back off. You will see a wire connected to each wheel:
Posted Image

My guess is that is the problem...make sure it is soldered correctly and that the clip is connected fine.

For the future, if you have any other jog wheel problems, you can simply pry that little lock off, pop the wheel off, and blow the optical sensor out with compressed air.

That fixed a dead jog wheel for me (which had the opposite symptoms from you, the touch worked but the platter movement was not picked up).
0

#3 User is offline   azzi 

  • Member
  • Group: Members
  • Posts: 11
  • Joined: 21-November 12

Posted 03 September 2015 - 01:00 PM

Eljeffe, thanks for the quick return. I will check and write here the result! hug [thumbup]
Music is my life!
0

#4 User is offline   azzi 

  • Member
  • Group: Members
  • Posts: 11
  • Joined: 21-November 12

Posted 07 September 2015 - 01:39 PM

Eljefee, Unfortunately it did not work ... I opened my device, cleaned with compressed air, and I fixed clips, I reset the system, but to no avail ... [thumbdn] HELP ME, PLEASE!
Music is my life!
0

#5 User is offline   eljeffe 

  • Member
  • Group: Members
  • Posts: 47
  • Joined: 02-March 15

Posted 08 September 2015 - 08:31 PM

Did you make sure those cables were soldered properly? That is really the only guess I got.
0

#6 User is offline   Ca1ibrat0r 

  • Newbie
  • Group: Members
  • Posts: 1
  • Joined: 20-September 15
  • LocationUkraine

Posted 05 October 2015 - 02:30 PM

Hello.
I had a similar problem.
The problem is in a metal disk jog, who had little contact with the metal stem, to which the contacts are connected, it is necessary to remove and gently pull out of the plastic plates.
You can put a piece of foil or other conductive material between the spindle and the disk jog.
Good luck!)
The only thing that happened for me, one of the disks accidentally dropped on the floor and broke into pieces, and now, I also ask for help, maybe someone knows where I can buy a spare disk ??((
0

#7 User is offline   TheMoroney 

  • Member
  • Group: Members
  • Posts: 57
  • Joined: 14-May 15
  • LocationUSA

Posted 10 February 2017 - 01:13 AM

Pm me and I might be able to help you
Author of the Numark DJ2GO script for Deckadance
Author of the Numark Orbit script for Deckadance
Author of the updated version of the script for the M-Audio Xponent
Deckadance user since 2014
FL Studio user since 2013
The Unofficial Numark and M-Audio Script writing person.
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users