Gibson Brands Forums: Gibson sg Setup questions? - Gibson Brands Forums

Jump to content

Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Gibson sg Setup questions?

#1 User is offline   roddick1993 

  • Newbie
  • Group: All Access
  • Posts: 1
  • Joined: 14-January 19

Posted 14 January 2019 - 02:45 PM

Hey,

I have a Gibson Sg that I'm currently setting up. I originally had it setup for high action for slide playing similar to Derek Trucks. I now want to just get it down to standard specs by Gibson. I changed the strings, checked the neck which I had to add a bit of relief to the truss rod. Next I checked the action as it was higher than normal. I brought the low E string high down to 1.98mm or rather just 2mm. Got it as close as I could. For the high e string the height was just above 2mm as well which is fairly high. The issue I'm having is that there's already fret buzz/rattle above the 12th fret, more above the 15th fret but can act up below that as well. So if I were to lower my action anymore then I would assume I'd get even more buzz/rattle. Also, if I bend just a whole tone it's pretty stiff and difficult. I have 10-46 on my sg. With 9's I break them too easily. Right now almost all the strings are just a hair or 2 above the back of the bridge. I had the high e and b strings really pressed against it, so I raised the saddle just a bit. Should I give the truss rod a 1/4 turn more of relief? Or is it more do do with the action/bridge?

Thanks
0

#2 User is offline   Twang Gang 

  • Advanced Member
  • Group: All Access
  • Posts: 1379
  • Joined: 26-November 12
  • LocationLake Keowee, SC

Posted 11 February 2019 - 05:20 PM

Hopefully you've solved this problem as the post is month old. But if not I would tend to think that there is too much relief in the neck, and you need to make the neck straighter (flatter) - this will make the strings more parallel to the neck all the way from nut to bridge and prevent the buzzing.

Gibson's set up specs say to get the fingerboard completely straight then back off the truss rod nut 1/8th of a turn for slight relief. (always loosen truss rod nut first then adjust back to where you want it).

I don't have metric measurements, but their specs say string height at the 12th fret should be about 3/64 in. for high E and 5/64 in. for low E. These are from top of the fret to bottom of the string.

As to the strings touching the back of the bridge - don't move the bridge saddles up and down, move the stopbar up to get the strings away from the bridge (assuming it's a Nashville bridge). If you have an ABR-1 bridge the strings will clear with the stopbar all the way down to the body.

Hope that helps.

This post has been edited by Twang Gang: 11 February 2019 - 05:34 PM

2017 Custom Shop 356 Mahogany/Maple Antique Natural
2017 Les Paul Standard T Honeyburst
2013 L5-CES Natural (Maple/Spruce)
2013 Les Paul Custom Lite (Mahogany/Maple) Ebony
2007 Taylor Solid Body Custom (Sapele/Walnut)
2018 Taylor 814 CE DLX (Rosewood/Spruce)
1981 Ovation Balladeer
1963 Walthari Mittenwald Classical
Rivera Venus 6 (1 X 12)Combo
Blackstar HT-5R (1 X 10) Combo
AER Compact 60-2
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users