Gibson Brands Forums: DJControl Inpulse 200 & 300 - Gibson Brands Forums

Jump to content

Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

DJControl Inpulse 200 & 300 Controller script

#1 User is offline   DJ Phatso 

  • Member
  • Group: All Access
  • Posts: 24
  • Joined: 02-September 15

Posted 15 January 2019 - 02:36 PM

Here are the mapping files for the Hercules DJControl Inpulse 200 & 300 for the latest version of Deckadance (2.72):


Browser:

Browser Knob = Playlist up/down (Blue ring LED) - Directory up/down (Green ring LED) .
Browser button = Switch betwenn Playlist and Directory.


LOAD A = Load track to deck A / Expand - Collapse (when in Directory view)
LOAD B = Load track to deck B

ASSISTANT = Automix
(IMPORTANT!!: Be sure to create an Automix playlist before using).




Decks:

Sync = Sync lock.

SHIFT + SYNC = Sync master

Cue = Cue point

SHIFT + CUE = Return to beginning of loaded song.

Play = Play/Pause.


Vinyl = Scratch On/Off (Default: ON)

SLIP = Snap

Q = Key Lock


Loop section:


Loop In = Loop In

Loop In (Long press) = Loop on/off (4 beat)

SHIFT + Loop In button = Loop Half size

Loop Out = Loop Out

SHIFT + Loop Out button = Loop Double size



FX Section :

Button 1 = FX3 on/off (Reverb)

Knob 1 = FX 3 parameter.

Knob 2 = FX Dry/Wet.


PADS - Hot Cue:

[Inpulse 300]

Pad 1-8 = Set and trigger Hot Cue 1-8.

Shift + Pad 1-8 = Delete Hot Cue 1-8.

[Inpulse 200]

Pad 1-4 = Set and trigger Hot Cue 1-4.

Shift + Pad 1-4 = Delete Hot Cue 1-4.


PADS - Roll Mode:

[Inpulse 300]
Pad 1-8 = Temporary loop ( 1/32 to 4 beat) + Leap (when you end looping playback resumes from where it would have been without looping).

[Inpulse 200]
Pad 1-4 = Temporary loop ( 1/2 to 4 beat) + Leap (when you end looping playback resumes from where it would have been without looping).


PADS - Slicer (Inpulse 300 only):


Pad 1-8 = Trigger Gross Beat Slot A1 - A8 (Gross Beat B1 - B8 on Deck B )



PADS - Sampler:

[Inpulse 300]
Pad 1-8 = Trigger Sampler 1-8 (Same for Deck B )

[Inpulse 200]
Pad 1-4 = Trigger Sampler 1-4 (Same for Deck B )


PADS - Toneplay (Inpulse 300 only):


Pad 1-8 = Trigger + 3 to -4 semi-tone cue points

PADS - FX :

NOTE: In FX mode, the pads sends multiple MIDI messages that affects various parameters in order to create "automatic effects" when pressed.

[Inpulse 300]

Pad 1 = FX2 on/off (Phaser)
Pad 2 = FX2 on/off (Distortion)
Pad 3 = FX2 on/off (Low Pass)
Pad 4 = FX2 on/off (Delay)
Pad 5 = FX2 on/off (Flanger)
Pad 6 = FX2 on/off (Low pass)
Pad 7 = Cue Point + baby scratch
Pad 8 = baby scratch


[Inpulse 200]

Pad 1 = FX2 on/off (Phaser)
Pad 2 = FX2 on/off (Distortion)
Pad 3 = FX2 on/off (Delay)
Pad 4 = baby scratch


PADS - SlicerLoop (Inpulse 300 only - NOT USED) :

PADS - Beatjump (Inpulse 300 only) :

Pad 1-4 = Beat LED Deck A
Pad 5-8 = Beat LED Deck B


Other controls as labeled.

--------------------------------------------------------------------------------

Attached File(s)


The Phat one!

Hercules DJ Support Team
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users