Jump to content
Gibson Brands Forums

Thunderbird Pro Wiring Diagram


Recommended Posts

Did somebody try to connect original pickups in parallel mode(shielding and white wire together and red wire as the signal one)? How does it sound? Since the impedance of single stock pickup is 7k, then impedance in this way should be 1/3,5k+1/3,5k)=1/?.....1,75k. Isnt this value too low and signal too weak?

Link to post
Share on other sites
  • 7 years later...

I had a TBird pro  with a great hum noise issue. After I've read this forums (and others) I came up with, what I think is the correct solution. Here I share with you

1) The wiring schematics in the page are correct

2) I don't think the preamp is the SD BEQ-2, just another two band preamp. I remember searching for it with the part number and finding it ,,,but not at SD

3) I don't think that changing the volume pot for 250K would yield aa 3dB volume gain (much less a 6dB gain with 512K). If you look closely at the schematic, you see you get the signal straight from the preamp output pin when the volume is maxed. Howeve rthere might be a small increase  in volume depending on the amplifier input impedance

4) The pickups are PASSIVE with an active preamp (as this is the most common configuration on active basses). There's no such thing as ACTIVE/PASSIVE pickups. EVERY BASS (and guitar for that matter) than can work both as active/passive, is a passive pickup/active preamp combination, changing to passive simply bypasses the preamp. One of the the wiring diagrams in this thread confirms this.  The RED WIRE in the pickup is for coil splitting, you can definitely check this with a multimeter, it's NOT FOR POWERING THE PICKUP. However, as the noise is picked by the pickup coils, running a current through them might mitigate the problem.

5) The correct approach is to properly shield the pickup cavities   with copper foil, o painting it with conductive painting.  (in my case the preamp cavity was painted with conductive paint, but you could check yours)

6) Note that it also has to be properly grounded, all pots bodies bust be grounded, and if you use copper foil or paint with conductive painting, this is already done

Hope this is useful

             Antonio

 

Link to post
Share on other sites
  • 10 months later...

Hello folks,

 

 I’m working on one of these basses for a friend. It is the full active model. 
 

When I plug the output cable in, sound comes out of the bass for about 2 seconds and then fades off to nothing rather quickly. The battery is minty fresh. 
 

Anyone have any tips on solving this?  I thinking of verifying all the wiring is per the diagram in this thread, and then maybe replacing the module if I don’t find any discrepancies. 
 

Thoughts?

 

 Thanks. 
 

Michael

Link to post
Share on other sites
  • 2 weeks later...

Hello again, Folks.

Hey, I'd really really appreciate your help on this....I want to purchase a replacement premap module for this bass.  I called Epiphone directly and they told me that I'd have to go to a dealer and have them order it.  I went to (large) dealer and they tell me that their Gibson/Epiphone support person is not responding to the inquiry....multiple tries over 3 weeks.

I'm at a loss on this....how can I get a replacement preamp?  

Thanks in advance for any support you can provide.....really.

 

IMG_3566 (2).jpg

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...