Sailor Bob C Posted August 5, 2021 Share Posted August 5, 2021 Recently purchased the P90 version of LP Special Tribute DC AND AM UNABLE TO LOWER NECK PICKUP FAR ENOUGH TO BALANCE WITH THE SLIGHTLY UNDERPOWERED BRIDGE PUP. So, have purchased a Dream 180 for the bridge to quiet hum and add needed balls...... still need to get that neck P90 lower....Any suggestions? Thanks in advance Quote Link to comment Share on other sites More sharing options...
Rabs Posted August 5, 2021 Share Posted August 5, 2021 You cant get it lower unless you want to route out the wood in the pocket.. Because of the way they screw in to the body, if you could screw them in lower the screws would be in great danger of going right through the body..... Thats why if you look in pickup hole you will see there is a physical ledge of wood to stop it going any lower. Quote Link to comment Share on other sites More sharing options...
jdgm Posted August 5, 2021 Share Posted August 5, 2021 I have exactly the same thing with the stock P90s in my LP Custom (avatar<). That's the way it is I'm afraid. You could try raising the bridge pickup or its polescrews but I doubt it would improve things. The neck pickup, being on or very near a harmonic point, is intrinsically louder than the bridge; I think your solution is a good one. Not worth routing out the wood IMO. I don't want to change my pickups - though I'm tempted by a set of 'noiseless' Fralins - very expensive - so I used a pedal boost when I gigged the guitar. Best wishes 🎸 Quote Link to comment Share on other sites More sharing options...
mihcmac Posted August 5, 2021 Share Posted August 5, 2021 (edited) The LP Spec Trib DC uses height adjustment tabs at each end of the P90 pickup mounted to the Pickguard. While most other P90 LP's use a screw going through the PU with a spring under it. Since the LP Spec Trib DC P90 pickups are mounted to the Pickguard make sure nothing is obstructing the PU being lowered underneath like excess cable. If you remove the Pickguard and inspect it, you may also be able tweak the mounting tabs to get it lower, adjust the P90 height with the Pickguard off to get it as low as possible. The reinstall it making sure the pickguard doesn't bow.. Edited August 5, 2021 by mihcmac 1 1 Quote Link to comment Share on other sites More sharing options...
Rabs Posted August 5, 2021 Share Posted August 5, 2021 Ohh yeah.. Duhh.. Totally forgot about that design change... 1 Quote Link to comment Share on other sites More sharing options...
Larsongs Posted August 6, 2021 Share Posted August 6, 2021 Have you tried adjusting the Pole Piece screws on each Pickup to balance them out? Quote Link to comment Share on other sites More sharing options...
Robzoid Posted August 7, 2021 Share Posted August 7, 2021 I would say, if anything, the neck is overpowered. I think Gibson uses the same pickup for bridge and neck. Swapping magnets is pretty simple with P90s. I would try swapping the neck's A5's for some A2's. The A2 is a weaker magnet, which will fix your problem. It'll also sound great. 1 Quote Link to comment Share on other sites More sharing options...
Rabs Posted August 7, 2021 Share Posted August 7, 2021 12 hours ago, Robzoid said: I would say, if anything, the neck is overpowered. I think Gibson uses the same pickup for bridge and neck. Swapping magnets is pretty simple with P90s. I would try swapping the neck's A5's for some A2's. The A2 is a weaker magnet, which will fix your problem. It'll also sound great. If that is the case then would it not be just easier to swap the pickups around rathe than dismantle them? Quote Link to comment Share on other sites More sharing options...
Robzoid Posted August 7, 2021 Share Posted August 7, 2021 Quote 59 minutes ago, Rabs said: If that is the case then would it not be just easier to swap the pickups around rathe than dismantle them? I'm able to switch the magnets out but I don't know how to solder so I can't change the pickups myself. So, for me it's easier. It's also much cheaper. But yeah, if you want to get a new pickup, an alnico 2 p90 like a Duncan Antiquity would be a good route. You can also have a luthier directly mount the neck p90 to the wood of the body. This will allow you to have the pick up as low as you want. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.